10 Things You Learned In Kindergarden Which Will Aid You In Obtaining Remote Key Repair
How to Fix a Key Fob That isn't Working
If your key fob doesn't work There are a few simple steps that can fix it. First, make sure that it's not your backup remote.
If the backup is able to lock and unlock your car door, it is most likely an issue with the main remote. The most common causes of car remote key failure are issues with the circuitry or battery.
Battery
It is not unusual for the battery in the car key fob to wear out. It is quite simple to change out the battery, however it is crucial to ensure that you choose the correct type that you can refer to your owner's manual or contact the manufacturer's dealer to find out the kind of battery you need. It is also a good idea to inspect the battery compartment thoroughly since dead batteries may leak harmful chemicals that can damage the remote. If changing the batteries doesn't solve the issue it could be because there are other issues that require attention by a professional. If buttons are stuck or broken for instance it might be necessary to disassemble the remote and rework each component. You could also try reprogramming your vehicle to recognize the new key fob.
Buttons
From frequent use, key fobs may get dirty and worn. This is not atypical, but it can cause buttons to cease functioning or require a difficult press to get them to work. This can be extremely frustrating particularly if you're out of town and need to start your vehicle. Fortunately, even worn-out or malfunctioning buttons can often be fixed with a little time and a few items you might already have in the home.
First, verify that the batteries are properly inserted and that the indentation at the back of the button has been filled. Then, carefully open up the remote and examine the circuit board. Check for indications of rust or other signs the buttons are damaged or worn. For instance, conductive paint may be missing. Use a Q-tip dipped into rubbing alcohol to gently clean any membrane contact that has damaged or where conductive paint is missing. Avoid rubbing too hard, as this can erode the conductive paint and stop the button from firing when it is it is pressed.
Also, carefully check the battery connector's terminals for a loose solder connection. If this is the case, connecting them back may bring back function to the button. You can apply the same method to restore functionality to any other loose connection in the fob.
If, for instance, any of the rubber buttons on the front of the key fob aren't functioning or require a long press to function it is likely that the graphite disks on the back of the button are deteriorating and require replacement. This can be done by rubbing a pencil across the disks, which should bring the button back to its original state.

If none of these solutions work or you not be able to get the button respond when pressed hard, it could be that the circuitry has failed. key fob repair near me G28CarKeys is possible to fix this issue by cleaning and re-soldering the button however, you should have a spare in case it does not work.
Circuitry
The circuit board inside the remote control could be dirty, regardless of whether the buttons on the key fob function or not. This issue can be fixed through a thorough examination. Broken and damaged cases are the most frequent causes of dirty boards. A damaged case could allow water and other debris to enter the circuit board, causing it to short out. Water can also eat through pins and vias, which are the tiny connectors that are found on the board.
If you're able to open your key fob and don't mind a little mess, we can remove the solder from the buttons and solder new ones in their place. It's also worth looking at the battery terminal connections. If they're loose, the buttons might not work or even become stuck in their down position. Soldering terminals and buttons back into place is usually enough to bring a non-working fob to a working condition.
Non-Remote Transponder Chips
Sealed non-remote transponder chips are much more durable than remote fobs that have them but they can still be damaged by a hole that is drilled into them or run over by a lawnmower or car door handle. Failures of the fuse are typically to blame for non-remote chips failures.
If you're not confident opening the key fob, take the circuit board off and use a multimeter to determine if the diode is functioning correctly. If you're not comfortable with this, go to your local Oreilly or hardware store and utilize their RF frequency tester. This will inform you whether the key fob sends a signal.
Programming
Key fobs are subject to lots of abuse and aren't indestructible. They can lose their pairing to the car's receiver because of shock or a low battery, which calls for the reprogramming. A professional auto locksmith or dealer will be able to reprogram your key fob and get it back up and running. In the event that resetting or repairing your key fob fails it could be the time to replace it all over again.